Visit for list of applicable patent(s), more information, or to request a quote. No warranty that product(s) will meet the stated specifications for customer specific applications or test equipment. Information/product(s) subject to change. 256 For dual shaft construction D Note: * Cable connector for C4, C5, C6 is AMP P/N 215083-6 or Equivalent (not for 32, 64 PPR) Rev. 312 For single shaft construction Schmitt trigger).
STRAIGHT PINS .05 CODE
Y00 (only available with A 5.0V Schmitt trigger) 3.3V (not for 64 PPR, No Detents B Code Bushing Length B 64 PPR) Z00 (only available with 0.
050 pitch X24 (only available with *C6 connector terminals (not Schmitt trigger) for 64 PPR) 32 PPR, No Detents Code Spec. 050 pitch 24 PPR, No Detents With Schmitt trigger, *C5 S connector terminals (not X00 (o nly available with Without locating lug for 64 PPR) Schmitt trigger) With Schmitt trigger, B 6 ribbon cable 24 PPR, 24 Detents With locating lug With. 050 pitch 5 positions 32, 64 PPR) *C4 lug, 32 and 64 PPR, see page 800 8 PPR, No Detents connector terminals (not Without Schmitt trigger, 8 for additional details) for 64 PPR) 600 6 PPR, No Detents A Without locating lug (not 5 ribbon cable 400 4 P PR, No Detents for 32, 64 PPR) With. 236 length Without Schmitt trigger, Inner shaft: 1.059 624 6 P PR, 24 Detents 4 ribbon cable BLANK W ith locating lug (not for (Not available with locating 416 4 P PR, 16 Detents With. 10 pitch pins Output Combination Dual shaft structure P1 Rear facing Code Spec. 050 pitch pins Single shaft structure Momentary TSS V1 Rear facing B S Slotted 22. T Code Termination Code Shaft Length L A None T F Flat.
STRAIGHT PINS .05 SERIES
Ordering Information Bushing Shaft Shaft Output Operating Switch Schmitt Trigger Series Termination Length Length Trim C Combinat i on Volt a ge & L oca ti ng L ug 291 V1 0 22 F 832 A B A S RTTT T T T T 2022124 1 2 1 E TTT E Code Spec. The options of Schmitt trigger, detents, momentary switch, shaft & bushing length, dual shaft, termination styles, torque, operating voltage, and IP ratings provide flexibility to meet your exacting design requirements. This product provides flexibility in resolution, power consumption, and operating temperatures. I am hoping that someone has possibly used a brand of dowel that has a nice finished end that may work for me.Series 291 Precision, Long-life 12mm Optical Encoder Available with 4, 6, 8, 24,32, 64 Pulses per Revolution Optional Momentary Switch Multiple options for terminations, resolution, cable lengths, and operating voltage Description The 291 Series allows versatility in design applications by providing highly reliable, precise digital output and long rotational life with our non-contacting design.
I would like to stay in the price range of a standard dowel pin and not get into hardened shafting.Īll the dowels seem to look nice in catalog pictures, but when I get them, they do not seem quite good enough for the application. I would like to have one end that is either crowned in a reasonably consistent manner (i.e., all of the crown should be convex and no part should be concave), or I would like to have one end that is cut off straight and flat with a reasonably consistent bevel.Īctually, if one end were just cut off straight and flat, and were reasonably smooth (like something that has been precision sawn), this could also work.
I only need one end of the dowel to look good, because only one end shows on the device. There are also black "dots" at each dowel end that look like some type of oxidation. The Mcmaster carr dowels have one end that is slightly beveled (but not cut flat) and they have one end that is slightly rounded on the outer edge (but slightly concave in the middle). It is hard to tell by looking at pictures in most catalogs what the dowel ends will really look like when you get them. The Mcmaster carr dowels are not what I am looking for as far as aesthetics go.
0 kommentar(er)
